81 lines
2.9 KiB
Plaintext
81 lines
2.9 KiB
Plaintext
# Generated by stepconf 1.1 at Mon Apr 7 16:11:26 2025
|
|
# If you make changes to this file, they will be
|
|
# overwritten when you run stepconf again
|
|
loadrt [KINS]KINEMATICS
|
|
loadrt [EMCMOT]EMCMOT base_period_nsec=[EMCMOT]BASE_PERIOD servo_period_nsec=[EMCMOT]SERVO_PERIOD num_joints=[KINS]JOINTS
|
|
loadrt hal_parport cfg="0 out"
|
|
setp parport.0.reset-time 5000
|
|
loadrt stepgen step_type=0,0,0
|
|
|
|
addf parport.0.read base-thread
|
|
addf stepgen.make-pulses base-thread
|
|
addf parport.0.write base-thread
|
|
addf parport.0.reset base-thread
|
|
|
|
addf stepgen.capture-position servo-thread
|
|
addf motion-command-handler servo-thread
|
|
addf motion-controller servo-thread
|
|
addf stepgen.update-freq servo-thread
|
|
|
|
setp parport.0.pin-01-out-invert 1
|
|
net spindle-on => parport.0.pin-01-out
|
|
net xdir => parport.0.pin-02-out
|
|
net xstep => parport.0.pin-03-out
|
|
setp parport.0.pin-03-out-reset 1
|
|
net ydir => parport.0.pin-04-out
|
|
net ystep => parport.0.pin-05-out
|
|
setp parport.0.pin-05-out-reset 1
|
|
net zdir => parport.0.pin-06-out
|
|
net zstep => parport.0.pin-07-out
|
|
setp parport.0.pin-07-out-reset 1
|
|
net home-x <= parport.0.pin-10-in
|
|
net home-y <= parport.0.pin-11-in
|
|
net home-z <= parport.0.pin-12-in
|
|
|
|
setp stepgen.0.position-scale [JOINT_0]SCALE
|
|
setp stepgen.0.steplen 1
|
|
setp stepgen.0.stepspace 0
|
|
setp stepgen.0.dirhold 45000
|
|
setp stepgen.0.dirsetup 45000
|
|
setp stepgen.0.maxaccel [JOINT_0]STEPGEN_MAXACCEL
|
|
net xpos-cmd joint.0.motor-pos-cmd => stepgen.0.position-cmd
|
|
net xpos-fb stepgen.0.position-fb => joint.0.motor-pos-fb
|
|
net xstep <= stepgen.0.step
|
|
net xdir <= stepgen.0.dir
|
|
net xenable joint.0.amp-enable-out => stepgen.0.enable
|
|
net home-x => joint.0.home-sw-in
|
|
|
|
setp stepgen.1.position-scale [JOINT_1]SCALE
|
|
setp stepgen.1.steplen 1
|
|
setp stepgen.1.stepspace 0
|
|
setp stepgen.1.dirhold 45000
|
|
setp stepgen.1.dirsetup 45000
|
|
setp stepgen.1.maxaccel [JOINT_1]STEPGEN_MAXACCEL
|
|
net ypos-cmd joint.1.motor-pos-cmd => stepgen.1.position-cmd
|
|
net ypos-fb stepgen.1.position-fb => joint.1.motor-pos-fb
|
|
net ystep <= stepgen.1.step
|
|
net ydir <= stepgen.1.dir
|
|
net yenable joint.1.amp-enable-out => stepgen.1.enable
|
|
net home-y => joint.1.home-sw-in
|
|
|
|
setp stepgen.2.position-scale [JOINT_2]SCALE
|
|
setp stepgen.2.steplen 1
|
|
setp stepgen.2.stepspace 0
|
|
setp stepgen.2.dirhold 45000
|
|
setp stepgen.2.dirsetup 45000
|
|
setp stepgen.2.maxaccel [JOINT_2]STEPGEN_MAXACCEL
|
|
net zpos-cmd joint.2.motor-pos-cmd => stepgen.2.position-cmd
|
|
net zpos-fb stepgen.2.position-fb => joint.2.motor-pos-fb
|
|
net zstep <= stepgen.2.step
|
|
net zdir <= stepgen.2.dir
|
|
net zenable joint.2.amp-enable-out => stepgen.2.enable
|
|
net home-z => joint.2.home-sw-in
|
|
|
|
net estop-out <= iocontrol.0.user-enable-out
|
|
net estop-out => iocontrol.0.emc-enable-in
|
|
|
|
net tool-change <= iocontrol.0.tool-change
|
|
net tool-changed => iocontrol.0.tool-changed
|
|
net tool-number <= iocontrol.0.tool-prep-number
|
|
net tool-prepare-loopback iocontrol.0.tool-prepare => iocontrol.0.tool-prepared
|