# #####################################################################
# # KlackEnder- Macros
# #####################################################################

[homing_override]
# set_position_z:0 # Make printer think Z axis is at zero, so we can force a move upwards away from build plate
# axes: z #will only call override if x is involved in the homing call
gcode: 
  {% set svv = printer.save_variables.variables %}
  {% if  svv.probe_attached == True %}
      { action_raise_error("Probe is attached!") }
  {% else %}
      G28 {rawparams}
  {% endif %}

[gcode_macro SCREWS_TILT_CALCULATE]
rename_existing: _SCREWS_TILT_CALCULATE
gcode:
  G28 ; Should always home before calculation even if already homed
  PROBE_ATTACH
  _SCREWS_TILT_CALCULATE
  PROBE_DOCK

[gcode_macro FORCE_PROBE_ATTACH]
gcode:
  SAVE_VARIABLE VARIABLE=probe_attached VALUE={ True }

[gcode_macro FORCE_PROBE_DOCK]
gcode:
  SAVE_VARIABLE VARIABLE=probe_attached VALUE={ False }

[gcode_macro TEST_IF]
gcode:
  {% if not 'xyz' in printer.toolhead.homed_axes %}
    { action_raise_error("Must Home Axis First!") }
  {% endif %}
  
  { action_respond_info("osie wyzerowane") }

[gcode_macro PROBE_ATTACH]
gcode:
  {% set svv = printer.save_variables.variables %}
  {% if not 'xyz' in printer.toolhead.homed_axes %}
    { action_raise_error("Must Home Axis First!") }
  {% endif %}
  
  {% if  svv.probe_attached == True %}
    { action_respond_info("Probe is already attached!") }
  {% else %}
    G90
    G1 Z20
    G1 X244 F8000
    G1 Z5
    G1 Z20
    G1 X0 F8000
    SAVE_VARIABLE VARIABLE=probe_attached VALUE={ True }
  {% endif %}

[gcode_macro PROBE_DOCK]
gcode:
  {% set svv = printer.save_variables.variables %}
  {% if not 'xyz' in printer.toolhead.homed_axes %}
    { action_raise_error("Must Home Axis First!") }
  {% endif %}
  
  {% if  svv.probe_attached == False %}
    { action_respond_info("Probe is already docked!") }
  {% else %}
    G90
    G1 Z20
    G1 X244 F8000
    G1 Z1
    G1 X0 F8000
    SAVE_VARIABLE VARIABLE=probe_attached VALUE={ False }
  {% endif %}

[gcode_macro BED_MESH_CALIBRATE] #macro with parameter passing
rename_existing: _BED_MESH_CALIBRATE
gcode:
  PROBE_ATTACH
  _BED_MESH_CALIBRATE {rawparams}
  PROBE_DOCK

[gcode_macro G29] #reliant on the macro above
gcode:
  BED_MESH_CALIBRATE

[gcode_macro PROBE_CALIBRATE]
rename_existing: _PROBE_CALIBRATE
gcode:
  PROBE_ATTACH
  G90
  G1 Z20
  G1 X95 Y86 F8000 ; Readjust for center of bed adjusted for probe offset
  _PROBE_CALIBRATE
  TESTZ Z=20

[gcode_macro PROBE_ACCURACY]
rename_existing: _PROBE_ACCURACY
gcode:
  PROBE_ATTACH
  G90
  G1 X95 Y86 F8000 ; Readjust for center of bed adjusted for probe offset
  _PROBE_ACCURACY
  PROBE_DOCK